工厂直销LED5730暖白灯珠金线2.8-3.4V/80显指灯珠光源--荧月电子
- 买家还在看 -
联系信息
- 夏明辉 先生 (总经理)
- 尊龙人生就是搏网站尊龙人生就是搏网站尊龙人生就是搏网站电话: 查看尊龙人生就是搏网站尊龙人生就是搏网站尊龙人生就是搏网站电话号码
- 传真:0769-83302571
- 尊龙人生就是搏网站尊龙人生就是搏网站尊龙人生就是搏网站地址: 广东省 东莞市 大朗镇 广东省东莞市大朗镇盆古庙区153号
产品详情
“工厂直销LED5730暖白灯珠金线2.8-3.4V/80显指灯珠光源--荧月电子”参数说明
品牌: | 其他 | 型号: | YT-5730W0S1 |
功率: | 0.5 | 光通量: | 45-50/50-55/50-60 |
发光角度: | 120 | 是否跨境出口专供货源: | 否 |
1000小时常规老化: | 100 | 色温区间: | 2800-3100 |
支架材质: | PPA | 产地: | 东莞 |
正向电压: | 2.8-3.4 | 允许结温: | 115 |
荧光粉品牌: | 英特美 | 反向电压: | 5 |
货号: | 123456 | 发光效率: | 130 |
导线材质: | 金线 | 显色指数: | 80 |
芯片尺寸: | 1530 | 是否通过LM-80测试: | 否 |
芯片品牌: | 三安 | 热阻: | ≤5 |
胶水品牌: | 信越 | 6000小时常规老化: | 100 |
额定电流: | 0.15 | 订货号: | 4647894654 |
尺寸规格: | 5730 | 是否进口: | 否 |
电压温度系数: | 40 | 色容差: | 5 |
静电击穿电压(ESD): | 1000 |
“工厂直销LED5730暖白灯珠金线2.8-3.4V/80显指灯珠光源--荧月电子”详细介绍
YT5730W0S1
Features(特征)
? PLCC-2 Package.(PLCC-2 封装)
? Extremely wide viewing angle.(宽的发光角度)
? Suitable for all SMT assembly and solder process.(适用于所有的SMT组装和焊接工艺)
? Available on tape and reel.(适用于载带及卷轴)
? Moisture sensitivity level: Level 4.(防潮等级Level 4)
? Package:2500pcs/reel..(包装每卷2500PCS)
? RoHS compliant. (RoHS 认证)
Description(描述)
The White LED which was fabricated using a blue chip and the phosphor
白光LED由蓝光芯片与荧光粉激发而成
ATTENTION
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE
SENSITIVE DEVICES
注意:操作时应注意静电敏感
Applications(应用)
■ Optical indicator(光学指示)
■ Indoor display(室内显示)
■ Automotive lighting(尊龙人生就是搏网站照明)
■ Backlight for LCD, switch and Symbol, display
(LCD背光、转换器,开关和标志,显示器等)
■ Tubular light application(用于日光灯管)
■ General use(一般应用)
Cautions注意事项
, the pressure on the silicone resin should be proper.
LED封装为硅胶,故LED胶体表面较软,用力按压胶体表面会影响LED可靠性,因此应有预防措施避免在封装的零件上的强大压力,当使用吸嘴时,胶体表面的压力应是恰当的。
Handling Precautions处理防备措施
Compare to epoxy encapsulant that is hard and brittle,,, Special handling precautions must be observed during assembling using sili- cone encapsulated LED products, Failure to comply might leads to damage and premature failure of the LED.
相对环氧树脂较脆较硬而言,硅胶封装较柔软且有弹性,虽然它的特性大大减少了热应力,但易受机械外力损坏,因此在手工处理方面须要对硅胶封装材料做预防措施,若未按要求操作,可能会导致LED损坏和光衰
- 1. 1. Handle the component along the side surface by using forceps or appropriate tools; do not directly touch or Handle the silicone lens surface, it may damage the internal circuitry.
通过使用适当的工具从材料侧面夹取,不可直接用手或尖锐金属压胶体表面,它可能会损坏内部电路
- 1. 2. be
-and-place machine to insure precise pickup and avoid damage during production.
为防止气压泄漏,SMD吸咀外径不可以超过LED尺寸,吸咀内径尺寸应尽可能大,吸咀顶端材质建议采用柔软材料以防在吸取期间刮伤或损坏LED胶体表面,元件的尺寸必须在取放机里准确的编程好,以确保 的吸取和避免生产过程中的损害
- 1. 3. circuitry
不可将模组材料堆积在一起,它可能会损坏内部电路
- 1. 4. Not suitable to operate in acidic envi- ronment, PH<7
不可用在PH<7的酸性场所
- 1. 5. LED operating environment and sulfur element composition cannot be over 100PPM in the LED
mating usage material.
LED工作环境及与LED适配的材料中硫元素及化合物成份不可超过100PPM
- 1. 6. When we need to use external glue for LED application products,,as most of LED packaging glue is silica gel, and it has strong Oxygen permeability as well as strong moisture permeability; in order to prevent ex- ternal material from getting into the inside of LED, which may cause the malfunction of LED, the single content of Bromine element is required to be less than 900PPM,the single content of CYTorine element is required to be less than 900PPM,the total content of Bromine element and CYTorine element in the external glue of the application products is required to be less than 1500PPM
当我们需要使用外封胶涂抹LED产品时,应确保外封胶与LED封装胶水相匹配,因为大多数LED的封装胶水为硅胶,它有较强的氧化性和较强的吸湿性,必须防止外封材质进入LED内部以造成LED的损伤,单一的 元素含量要求小于900PPM,单一氯元素含量要求小于900PPM,在涂抹LED产品时要求外封胶 元素与氯元素总含量必须小于1500PPM
查看更多产品> 向您推荐
内容声明:您在尊龙人生就是搏网站采购商品属于商业贸易行为。以上所展示的信息由卖家自行提供,内容的真实性、准确性和合法性由发布卖家负责,请意识到互联网交易中的风险是客观存在的。
价格说明:该商品的参考价格,并非原价,该价格可能随着您购买数量不同或所选规格不同而发生变化;由于尊龙人生就是搏网站不提供线上交易,最终 格,请咨询卖家,以实际 格为准。